2
Anonymous posted an answer for this 1979 Suzuki GS 750 E:
"my clutch lever is increasingly difficult to operate and by the end of my ride my forearm..."
AnonymousAnonymous posted an answer for this 1979 Suzuki GS 750 E:
"Yeah, you gotta lube the cable sometimes. It's important, 'cause if the cable hangs up the..."
Anonymous
Anonymous posted an answer for this 2003 Yamaha YZ 250:
"ive got a 96 yz250 its got pieces of the piston and the sleve in the crank case can i get..."
AnonymousAnonymous posted an answer for this 2003 Yamaha YZ 250:
"I think you can clean it up without splitting the cases, but I'd pull it from the frame so..."
Anonymous
Anonymous posted an answer for this Vacuums:
"Remove the covers as far as you are able to and oil every point where two or more pieces..."
AnonymousAnonymous posted an answer for this Vacuums:
"my wife has a 910 Babylock Surger and I'd like to clean and oil it, where do I put a drop..."
Anonymous
Anonymous posted an answer for this Garden:
"This: http://www.amazon.com/Bosch-80111-Worm-Drive-Saw/dp/B0002EVD9G lp"
AnonymousAnonymous posted an answer for this Garden:
"I have a Skil worm drive saw and need to know what kind of oil to use."
AnonymousAnonymous posted an answer for this Echo Garden:
"Need the air gap between the ignition coil and the flywheel for an Echo PB-251 leaf blower"
AnonymousAnonymous posted an answer for this Echo Garden:
"All magnetos work best with minimal air gap. Gap it with the thinnest piece of..."
Anonymous
Anonymous posted an answer for this Audio Players & Recorders:
"Hello, If you're wanting to record your records to CD check the specs carefully- the..."
Anonymous
Anonymous posted an answer for this Euro-Pro 9120 Computerized Sewing Machine:
"Hello, Bottom thread issues are generally caused by either lack of lubrication, buildup of..."
AnonymousAnonymous posted an answer for this Euro-Pro 9120 Computerized Sewing Machine:
"I have exchanged this machine 3 times - now Target doesn't even carry it - the same..."
Anonymous
Anonymous posted an answer for this Husqvarna Rose:
"The bottom thread doesn't exactly 'feed', it is passive in that it's drawn out by the top..."
Anonymous
Anonymous posted an answer for this Ossa Motorcycles:
"I am restoring a 1972 MAR 250.At present it will not run due to lack of compression.Can..."
AnonymousAnonymous posted an answer for this Ossa Motorcycles:
"Faulty crank seals will certainly make a two-stroke hard to start, and can cause it to..."
Anonymous
Anonymous posted an answer for this Ford Cars & Trucks:
"spark plug gap setting for a 1973 ford f-250 p/up with a 390 v8"
AnonymousAnonymous posted an answer for this Ford Cars & Trucks:
".035" for the old big block Fords with breaker point ignition. lp"
AnonymousAnonymous posted an answer for this Troy-Bilt Garden:
"About the best place to get parts for these tillers now is eBay. MTD has owned the..."
AnonymousAnonymous posted an answer for this 1982 Ford F 150:
"I am trying to get TDC on #1 cyl 0n a straight 6 1982 Ford f150. Turning the crankshaft..."
AnonymousAnonymous posted an answer for this 1982 Ford F 150:
"Are you sure the distributor is all the way in? If it's hanging up the gear on the bottom..."
AnonymousAnonymous posted an answer for this Vacuums:
"A sewing machine should catch and tie the threads at any thread tension. If it's not tying..."
AnonymousAnonymous posted an answer for this Vacuums:
"Only every 10 or so stitches holds. Probably a tension problem, but I don't have a manual..."
AnonymousAnonymous posted an answer for this 1984 Ford Ranger:
"I have done just about everything to make it pass smog but it still runs rich. What can I..."
AnonymousAnonymous posted an answer for this 1984 Ford Ranger:
"How close is it? What fuel are you using? Higher-octane fuel is generally less rich than..."
Anonymous
Anonymous posted an answer for this 1992 Ford Bronco:
"Open the door and, facing the edge of the door, reach out and press your palms against the..."
Anonymous
Anonymous posted an answer for this Cub Cadet Street Sign- tractor lawn riding mower parts:
"That honestly seems like a lot of money to me for something produced by the MTD company...."
Anonymous
Anonymous posted an answer for this Toys:
"i have just bought my daughter a lambo 12 volt ride on and it just runs realy slow is..."
AnonymousAnonymous posted an answer for this Toys:
"Be sure the charger is working well. It should charge right to the outgassing point- 14.4V..."
Anonymous
Anonymous posted an answer for this 1994 Oldsmobile Cutlass Ciera:
"With heads that have a cam in them resurfacing is a non-option. If you resurface the head..."
AnonymousAnonymous posted an answer for this 1994 Oldsmobile Cutlass Ciera:
"warped cylinder head on 1994 Olds Cutlass Ciera... Options?"
Anonymous
Cars & Trucks 91 answers
Garden 27 answers
Vacuums 11 answers
Food Mixers 9 answers
Ovens 9 answers
Washing Machines 9 answers
Welding Tools 8 answers
Sewing Machines 8 answers
Toys 7 answers
Motorcycles 7 answers
