2If its already broken, what you got to lose.
Anonymous posted an answer for this Makita 18V 1/2"CRDLS Drill Kit:
"Your selector slide for the gears may be broken. If it is broken you will have to replace..."
Anonymous
Anonymous posted an answer for this Tools & Hardware - Others:
"You may want to check the battery connection terminal inside the housing. Sometimes the..."
Anonymous
Anonymous posted an answer for this Makita LXT202 BHP451 18 Volt Hammer Drill & BTD140 18 Volt Impact Driver Lithium Ion Combo Kit:
"If the motor is working good then check the hammer and anvil to see if they are rounded..."
Anonymous
Anonymous posted an answer for this Hitachi C10FCE2 10" Compound Miter Saw:
"There is no reset button on your motor. Sounds like you have a fried motor. You should be..."
Anonymous
Anonymous posted an answer for this Saws:
"One way is to lock your saw blade into a vise and remove the blade retainer. I am not sure..."
Anonymous
Anonymous posted an answer for this Hammering:
"I do not suggest disassembling this drill. Hilti offers a trade in program for a reason...."
Anonymous
Anonymous posted an answer for this Stanley Factory Reconditioned Bostitch U/RN46 1 1 3/4" Coil Roofing Nailer:
"You should check the check seal (61) for damage or weakness as well as the driver o-ring..."
Anonymous
Anonymous posted an answer for this Dewalt D51321 3/4" 1 3/4" Heavy Duty Coil Roofing Nailer, 70 120 Psi:
"You need to check the piston oring for damage. If the driver slides through the cylinder..."
Anonymous
Anonymous posted an answer for this Delta JT160 Shopmaster 10 Amp 6 Inch Benchtop Jointer:
"It sounds to me like you have a swollen field and/or armature. What happens in a situation..."
AnonymousAnonymous posted an answer for this Dewalt Saws:
"It really depends on the model. The clamshell set for the DW705 is $20. There are many..."
Anonymous
Anonymous posted an answer for this Dewalt Heavy Duty 2 Brad Nailer Compressor Combo Kit:
"Depending on the model that you have it is more than likely the piston seal/rings or the..."
AnonymousAnonymous posted an answer for this Dewalt Saws:
"There is no kit. There is a way to do it. The only catch is that it will probably wind up..."
Anonymous
Anonymous posted an answer for this Dewalt DC390K 18v Cordless Circular Saw Kit:
"You may be able to salvage the torsion spring that is there. Sometimes the end will break..."
AnonymousAnonymous posted an answer for this Saws:
"Most manufacturers do not cut a slot in the inserts for miter saws. Just use your saw as..."
Anonymous
Anonymous posted an answer for this Dewalt 18 Volt Compact Drill Kit:
"You will need to get part # 389025-00 which is the brush pair kit. Remove the 8 torx..."
Anonymous
Anonymous posted an answer for this Craftsman 3 gal. Air Compressor, 1.5 hp, Horizontal k:
"I don't believe it is either of the other two solutions. You more than likely have a..."
AnonymousAnonymous posted an answer for this Tools & Hardware - Others:
"You should be able to open the load cover and be able to remove the nail. Sometimes the..."
Anonymous
Anonymous posted an answer for this Craftsman Drills:
"It really depends on the model. Here is a general description of how to remove most..."
AnonymousAnonymous posted an answer for this Drills:
"It would be wise to have it serviced at a repair center. That is not an easy repair and it..."
Anonymous
Anonymous posted an answer for this Milwaukee Tool Milwaukee Orbital Jig Saw with L.E.D. 6268 - 21:
"Yes the Milwaukee 6268-21 does require the use of certain jigsaw blades. You have to use..."
AnonymousAnonymous posted an answer for this Black & Decker Saws:
"The JS200 jigsaw has a manual blade clamp so you will have to loosen the two screws on the..."
Anonymous
Anonymous posted an answer for this Stanley Bostitch CWC200ST 3HP Oil Lube Stack k Compressor:
"You will need to check the cylinder for scarring (deep vertical grooves or depressions in..."
Anonymous
Anonymous posted an answer for this Freud FT3000VCE Router:
"First thing to check is that your brushes are touching. Remove the 4 screws holding the..."
AnonymousAnonymous posted an answer for this Craftsman Saws:
"You could have a couple of different problems. The first place to start is the cord. A..."
AnonymousAnonymous posted an answer for this Craftsman 3 gal. Air Compressor, 1.5 hp, Horizontal k:
"You more than likely have a broken valve reed. What is happening is that your motor is..."
AnonymousAnonymous posted an answer for this Saws:
"The RPM's of the motor x the size of the pulley (3000rpm x 6inchs = 18000) = the output..."
AnonymousAnonymous posted an answer for this Delta Tools & Hardware - Others:
"Is it a single phase motor model 22-680, or a three phase motor model 22-681. The single..."
Anonymous
Anonymous posted an answer for this Stanley Bostitch N88rh Framing Nailer Driver Piston 158582:
"You have a crumbled trigger seal. You can order a new trigger valve through bostitch. It..."
Anonymous
Anonymous posted an answer for this Campbell Hausfeld 3 1/2" Rh Fram Nailer:
"You can use the same nails that are used for these nailers: Porter Cable FC 350A, Hitachi..."
AnonymousAnonymous posted an answer for this Skil Saws:
"Almost all of the Skil table saws are the same setup when it comes to the motor and drive..."
Anonymous
Anonymous posted an answer for this Bosch 13624 24V Cordless Hammer Drills:
"The brushes come as an assembly with the spring and brush in one unit. If your springs are..."
Anonymous
Saws 43 answers
Air Tools & Compressors 38 answers
Drills 21 answers
Tools & Hardware - Others 17 answers
Hammering 7 answers
Garden 6 answers
Measuring Tools & Sensors 3 answers
Vacuums 2 answers
Hardware & Accessories 1 answer
Crafts & Hobbies 1 answer
