Error code E50 what does this mean - Zanussi FJS1225W Front Load Washer

Pease don't type in all CAPS Anonymous, it is considered SHOUTING and is harder to read.

It is a motor circuit fault

I have a AEG Lavamat 72800 which doesnt start any cicle ...

JustAnswer https://www.justanswer.com > UK Appliance Repair
Oct 13, 2011 - Hi. Ok lets get the correct error code out. To do this turn the dial to any setting and let it light up. Then press and hold the rinse hold ...

1 answer · Top answer: Hi Ok E54 means motor relay contacts sticking or motor down to earth. The relays are ...

I keep getting a error E50 on my AEG Lavamat model ...

JustAnswer https://www.justanswer.com > UK Appliance Repair
Jul 5, 2012 - E50 is a motor circuit fault. Check the carbon brushes again, see if they've broken or stuck. Check the wiring to the motor. Let me know ...

1 answer · Top answer: Hiya, E50 is a motor circuit fault. Check the carbon brushes again, see if they'

https://www.google.com/search?q=AEG+LAVAMAT+72800+ERROR+CODE+50

..

https://smallbusiness.chron.com/brother-printer-code-e50-mean-59164.html

If you wish to get some details treadmill error codes and calibration ; check the site linked here. http://electro-medical.blogspot.com/

Family error code E50 means a problem with the washing motor. Family error code E70 means a problem with the NTC sensor. In my experience, E50 is most common fault in worn carbon brushes. But in any case family error code E50 is shown to the customer. In service mode could be: E51,52,53 and 54. The same applies to family E70 error code that will be displayed in service mode as error code E71 or E74.
E50 error code could be: motor winding, power board, tachymetric generator, motor relay on power board, wiring between motor and power board and wiring between tachymetric generator and electronic.
E70 error code could be: faulty NTC sensor, wrong position of NTC sensor or to much limescale on it and finaly wiring between NTC and electronic.

Dado

Hello Baldur Thor, thanks for your inquiry!
From what you have described your Electrolux air conditioner is displaying an "E50" error code. I do not show an "E50" has a valid error code. Could you please verify which appliance you are having issues with? Additionally, you could perform a reset on your air conditioner which is disconnecting the power from it for ten minutes. If you continue to have issues please reconnect. -Matt

e50 is a motor error code.check the motor brushes are ok and check the insulation on the motor as this will give you an e50 error code.could also be a faulty wiring loom to the motor or a faulty main control pcb

E50 says the motor is overheated, they recomen you let it sit for 30min to clear.
It can be the motor power supply triac has got a short circuit or there could be no signal from the motor tachometric generator, which will uaually mean a pcb fault, or wiring to motor or even the motor. hope this helps

hi,

The "E50" error code indicates formatting a storage card has failed.I think the e50 error code happens when the camera is reading and/or writing to the CF card when the battery are dead or real low. The camera does not get to finish writing data and leaves an error on the CF card. Use new battery or fully charged battery. I hope this may help you,

regards,
kaybicks

Brother error e50
The error code E50 indicates a fuser unit failure - the fuser unit is no longer working and needs replacing. The error may also display itself on your Brother printer's front display panel as "Fuser Unit Failure" or "Replace Fuser Unit."

What Does the Brother Printer Code E50 Mean? - Small ...

i can not find e50 in any of my servive manuals, are you sure it is e50 ?

The "E50" error code indicates formatting a CF card has failed. Solution To clear the "E50" error, try performing the following procedure. 1. Try using another CF card. If you have another CF card, try loading it in the camera. If the error code is not displayed when the other CF card is loaded, there may be something wrong with the first one rather than with the camera. 2. Use your computer's ScanDisk utility to check the CF card for errors. Use ScanDisk to check the CF card for card error or card failure. Refer to the instruction manual for your operating system or Windows Help for further instructions. (If you are using a Macintosh, use the "Disk First Aid" program to check for card error or card failure. Refer to the instruction manual for your Macintosh OS for further information.) Be sure to back up the data on the CF card on the computer before you check the CF card. If a card error or card failure occurs when you use your computer's ScanDisk, there is something wrong with the CF card. Follow ScanDisk's on-screen instructions to solve the problem.