E60 error code

Found These Fault Codes On Internet, Hope This Helps, Daz

ALARM CODES

E00(E00)- Problems with water fill during washing
-Tap closed; solenoid valve, water distributor, wiring ,main PCB, pressure switches

E01(E00)- Problems with water fill during drying
-Tap closed; solenoid valve, wiring , main PCB, pressure switches

E10(E10)- Problems with water drain during washing
-Drain hose kinked, filter blocked, drain pump, water distributor, wiring , main PCB, pressure switches

E11(E10)- Problems with water drain during drying
-Drain hose kinked, filter blocked, drain pump, pressure switches

E20(E20)- Door open
-Cycle in Door delay, wiring , main PCB

E21(E20)- Fault in door delay power triac
-Wiring , main PCB

E30- Fault in electronic pressure switch
-Electronic pressure switch, wiring , main PCB

E31- Fault in electronic pressure switch circuit
-Main PCB (fault in electronic pressure switch circuit)

E32(E10)-Calibration error in electronic pressure switch
-Electronic pressure switch, drain pump, wiring , main PCB, filter blocked

E33- Incongruency between electronic pressure switches and safety switch 1
-Electronic pressure switch, safety pressure switch,wiring, main PCB

E34- Incongruency between electronic pressureswitches and safety switch 2
-Electronic pressure switch, safety pressure switch,wiring, main PCB

E35- Intervention of anti-overflow pressure switch
-Solenoid valve, water distributor, wiring, main PCB,anti-overflow pressure switch

E36- Water leakage (maximum number of resets exceeded)
-Water leakage, drain hose too low, pressure switch,wiring, main PCB

E40- Motor power triac short-circuited
-Main PCB (triac short-circuited)

E41- No signal from tachimetric generator
-Tachimetric generator on motor, wiring, main PCB

E42- Fault in tachimetric generator circuit
-Main PCB (tachimetric generator sensing circuit)

E43- Intervention of motor overload protection
-Motor, wiring, main PCB

E50- Insufficient heating during wash phase
-NTC sensor setting incorrect, heating element, wiring,main PCB

E51- Overheating during wash phase
-Heating element (to earth), main PCB (relays)

E52- Insufficient heating during drying phase
-NTC sensor setting incorrect, safety thermostat,thermostats, drying heater, wiring, main PCB (relays)

E53- Overheating during drying phase
-Drying heater (to earth), main PCB (relays)

E55- Fault in power relay for heating element (K3)
-Safety pressure switch 2, wiring, main PCB- 6 -

E60- Fault in washing NTC sensor
-Washing NTC sensor, wiring, main PCB

E61- Fault in drying NTC sensor(condenser)
-Drying NTC sensor (condenser), wiring, main PCB

E62- Fault in drying NTC sensor(duct)
-Drying NTC sensor (duct), wiring, main PCB

E63- Fault in 1/2 power thermostat
-Drying NTC sensor (duct), 1/2 power thermostat, wiring,main PCB

E70- Power triac to distributor motor short-circuited
-Main PCB (triac short-circuited)

E71- Fault in power relay to distributor loads
-Main PCB (relay open)

E72- No distributor position signal
-Water distributor motor, wiring, main PCB

E73- Incorrect timing on distributor contacts
-Water distributor, wiring, main PCB

E90- Fault in tank fill pump
-Hoses obstructed, tank fill pump, wiring

E91- Fault in tank drain pump
-Hoses obstructed, tank drain pump, wiring

E92- Fault in power triac to tank fill pump
-Tank fill pump, wiring, main PCB

Our machine - a ZWF1437 - has developed the same problem. Our friendly engineer has checked his manual and told us that there is no such error code. He suggested switching the machine off and unplugging it to allow any residual charge to clear from the memory chip. The next step is to clean out the filter at the front - remember to empty the water out first. After a couple of hours, switch the machine on, press reset and then spin to empty any remaining water. Hopefully, this could work ---it didn't work on ours but he assures me that this tip usually works.

Hallo giebt es die seite auch auf deutsch?habe mein handbuch nicht mehr..meine waschmaschine zeigt e61 und dreht nicht.was tun??