"Load paper" When print command is clicked, a redlight in the middle comes with a message "load papers". How can you fix this situation. It used to work without this sign before.

actually there is a sensor that detects the papers once they are loaded. in some printers it wont detect the papers once we keep it. even tough papers are there in tray it wont detect it. just trying keeping papers in different positions. it will detect it.

advice would be always keep papers in reserve in the printer. dont let it make empty
actually there is a sensor that detects the papers once they are loaded. in some printers it wont detect the papers once we keep it. even tough papers are there in tray it wont detect it. just trying keeping papers in different positions. it will detect it.

advice would be always keep papers in reserve in the printer. dont let it make empty

even if different positions dont work out see if there is any obstacle in the\at makes the sensor not reachable to paper... it may be like fust or somethin.. u will have to clean it..

even after this its not detecting means please tell me..
even if different positions dont work out see if there is any obstacle in the\at makes the sensor not reachable to paper... it may be like fust or somethin.. u will have to clean it..

even after this its not detecting means please tell me..

paper drawer is completely full... no printing happens..

Trying to print documents - responce reads "load manual feeder with plain paper letter"

..if this is the problem solution is as follows..
The printer may be trying to draw paper from a source other than the
paper tray. Many printers have a hatch or slot in the front or on the
side in which one can load non-standard paper sizes and envelopes. It
may be trying to print there. Try to locate this place and put a few
pieces of paper in there.
paper drawer is completely full... no printing happens..

Trying to print documents - responce reads "load manual feeder with plain paper letter"

..if this is the problem solution is as follows..
The printer may be trying to draw paper from a source other than the paper tray. Many printers have a hatch or slot in the front or on the side in which one can load non-standard paper sizes and envelopes. It may be trying to print there. Try to locate this place and put a few pieces of paper in there.

paper drawer is completely full... no printing happens..right..
solution:
The printer may be trying to draw paper from a source other than the
paper tray. Many printers have a hatch or slot in the front or on the
side in which one can load non-standard paper sizes and envelopes. It
may be trying to print there. Try to locate this place and put a few
pieces of paper in there.
even after this its not detecting means please tell me..
paper drawer is completely full... no printing happens..right..
solution:
The printer may be trying to draw paper from a source other than the paper tray. Many printers have a hatch or slot in the front or on the side in which one can load non-standard paper sizes and envelopes. It may be trying to print there. Try to locate this place and put a few pieces of paper in there.
even after this its not detecting means please tell me..

if the paper is not detected itself then sensor must be bad..
sensor will be located near the edge of the slot where you input your papers..
if the paper is not detected itself then sensor must be bad..
sensor will be located near the edge of the slot where you input your papers..

this model uses a LED to transmit a light through a little section of
the empty toner cart. Its a little square area and should be located on
the backside of the empty toner cart. you will see the sensor that it
slides into. Make sure this area is clean.If this area is dirty you
will still have a error light.

my best guess would be there was spillage of toner on the sensors to
detect the waste basket overflowing, hence why the error message is
constant. This would require cleaning of the sensors, a relatively
simple task but for proper access, the machine would need to be
partially disassembles for thorough cleaning. It would be best done at
a repair centre.

See your manual:http://www.ricoh-usa.com/downloads/manua...
this model uses a LED to transmit a light through a little section of the empty toner cart. Its a little square area and should be located on the backside of the empty toner cart. you will see the sensor that it slides into. Make sure this area is clean.If this area is dirty you will still have a error light.

my best guess would be there was spillage of toner on the sensors to detect the waste basket overflowing, hence why the error message is constant. This would require cleaning of the sensors, a relatively simple task but for proper access, the machine would need to be partially disassembles for thorough cleaning. It would be best done at a repair centre.

See your manual:http://www.ricoh-usa.com/downloads/manuals/printers/cl2000.pdf